|
|
|
|
|
- The LOC-PAC Filter Housing is positive locking
mechanism factory assembled HEPA filter housing constructed
of 16 USS gage galvanized or stainless steel sheet metal components
as required.
- There are reinforced hinged access doors on each side for
ease of filter change.
- Perimeter 1/4" closed cell neoprene gasketing is provided
on each door to insure a minimum 99.97% efficiency
of units with HEPA filters installed.
- A brass cam-type double-acting positive sealing mechanism
provides proper seal strength of the HEPA filter to the HEPA
sealing plate. This mechanism can be operated from either side
of the unit.
- An integral 2" prefilter track is provided with each unit.
- The unit is capable of withstanding pressure to 4-5" w.g.
Special reinforced units are available for higher pressure service
(7-10" w.g.)
- All units are factory assembled for ease of installation.
Flanges provide ready connections to other HVAC equipment. Read
more... [119 K]
|
|
- Cabinet is constructed of 20 gauge (.0359) galvanized steel.
All cabinets are furnished with provisions for suspension at
all (4) top corners with 3/8" threaded rod and are equipped
with vibration isolators (or as specified).
- All cabinets are acoustically lined with a fiberglass
insulation manufactured by an approved vendor. Insulation
is secured with a non flammable contact cement. All exposed
edges and joints in insulation are sealed to eliminate shedding.
- Bearings are sealed ball type, isolated in rubber.
- Shaft material is ground and polished stress-relieved
steel, with flats and keyways to prevent slippage of driven
pulley.
- Open drip proof (or as specified). Motor is mounted
on an adjustable base.
- 208/230V 60HZ, 460/480 Optional.
- Units shall be classified to accommodate CFM ranges
of 2,000 CFM to 14,000 CFM and can be built to custom
specifications.
|
|
The Purolator ASHRAE PURO® Seal ASA
filter housing is a multistage unit for 2" or 4" prefilters, combined
with 1" header models of medium and high efficiency extended surface
SERVA-PAKT, AERO-CELLT, SERVA-CELL® and DEFIANT®
final filter products. A broad range of sizes are available to accommodate
most system requirements.
NOTE: Housing accommodates
6" through 36" filters, with as small
as 22-1/4" in-line depth required.
Each housing is constructed with specific
features which increase product versatility,
integrity, and ease of use.
Read more...
[308 K]
|
|
The Purolator ASHRAE PURO Seal FBA
filter housing is a single stage unit for 2”, 4”,6”
or 12” medium or high efficiency extended surface SERVA-PAK™,
AERO-CELL™, SERVA-CELL® and DEFIANT® final
filter products. A broad range of sizes are available to accommodate
most system requirements. Each housing is constructed with specific
features which increase product versatility, integrity, and ease
of use.
Factory assembled of 16-gauge galvanized steel into a one-piece construction with a 2",
4", 6" or 12" pre-formed galvanized track to
insure easy field installation.
Read more... [342 K]
|
|
The Purolator ASHRAE PURO Seal VBA
filter housing is a single stage unit. Our standard VBA housings
are 30" deep and accommodate various combinations of 2-inch or 4-inch
MARK 80-DT pleated, hi-E 40® pleated,
and Synthetic Support Panel basic and medium efficiency filters.
Each housing is constructed with specific features which increase
product versatility, integrity, and ease of use. Read more... [291
K]
|
|
The Purolator ASHRAE PURO® Lok ASA
filter housing is a multistage unit for 2" prefilters, combined
with 3/4" header models of medium and high efficiency extended surface
SERVA-PAKT, AEROCELLT, SERVA-CELL®or DEFIANT® final
filter products. This unique housing utilizes a mechanism that locks
down the final filter header to eliminate bypass. A broad range
of sizes are available to accommodate most system requirements.
NOTE: Housing accommodates 5-7/8" through 11-1/2" filters, with as
small as 19" in-line depth available.
Each housing is constructed with specific features
which increase product versatility, integrity, and ease of use.
Read more... [96
K]
|
|
The Purolator Carbon PURO-Seal CSA
filter housing is a multistage unit for 2" or 4" prefilters, combined
with 3/4" carbon trays designed to remove gas/vapor contaminants.
A broad range of sizes are available to accommodate most system
requirements. Each housing is constructed with specific features
which increase product versatility, integrity, and ease of use.
Weatherproofing: Refers to a pitched roof of 16-gauge material; also includes rainguard over the door.
Read more... [105 K]
|
|
Purolator's Bag-in/Bag-out side
access filter housing fulfills the requirements of gasket and fluid
seal application filtration while specifically providing safe replacement
of contaminated HEPA filters. By containing dangerous
by-products within the bag-in/ bag-out system, maintenance personnel
avoid direct contact with threatening particulate.
Factory assembled of 11- and 14-gauge stainless steel.
Seam welding reinforces joint strength and other points of pressure.
Reinforced to withstand up to 20" w.g., positive or negative. Read
more... [293 K]
|
|
For Commercial & Industrial applications requiring
gasket and fluid seal ULTRA-CELL® filtration-95%,
99.97% or 99.99% efficiency on .3 micron particulate-the Purolator
HSA state-of-the-art crank lock system provides consistent
compression and continuous sealing. A broad range of configurations,
with and without pre-filter tracks, are available to accommodate
most system requirements. Each housing is constructed with specific
features which increase product versatility, integrity, and ease
of use. Read more... [335
K]
|
|
Purolator's PURO Frame HEPA holding frame
is a 16- gauge galvanized steel HEPA holding frame that can be used
to hold filters individually, or be used in multiple banks. All
filters are held in place with individual clips to accommodate a
5-7/8" filter or an 11-1/2" filter frame. Each PURO-frame
HEPA holding frame is manufactured with several features of construction
which support use in a variety of HVAC applications-including gasket
or fluid seal-and ensure it will outperform the competition.
Available in 16-gauge galvanized steel or Type 304 stainless steel. Contact factory for pricing.
Read
more... [324 K]
|
|
Purolator's PURO Frame II is a
unique holding frame that can hold a HEPA and a pleated filter together
for front load access. All filters are held in place with individual
clips to accommodate a 5-7/8" HEPA filter or an 11-1/2" HEPA filter
frame. Each PURO Frame II HEPA holding frame is
manufactured with several features of construction which support
use in a variety of HVAC applications-including gasket or fluid
seal-and ensure it will outperform the competition. Read
more... [182 K]
|